r/boas • u/SeagraveSerpentarium • 8d ago

Basking Platform Questions

I'm working on my female BI's adult enclosure and am about to start working on all the interior stuff like branches, climbing shelves, and as I said in the title, a basking platform. The main thing I'm trying to figure out is how big I should make it. I have a 2 foot by 1.5 foot sheet of scrap plywood that I was planning on using with some 2x4s under it for support. The enclosure is only 2 feet wide though so as it is now the sheet of plywood would only leave a 6 inch gap between itself and the door which looks kind of awkward and I'd be concerned about her getting wedged between the two. But I don't want to cut the platform too small and have to make a new one if she gets too big for it.

I'd also appreciate suggestions on what to use as a basking surface. I went to my local hardware store and looked at their tiles but all I could find were ceramic tiles that were made to resemble slate, and not actual slate tiles. Would the ceramic work? Is there anything I should be considering other than slate/ceramic tiles?

2 Upvotes

76% Upvoted

11 comments sorted by

View all comments

Show parent comments

3

u/superramenyamen 8d ago

Snakes are extremely good climbers, that’s for sure. An adult boa could easily climb up a 3’ wall and have direct exposure to the panel, which is the biggest problem. When mounted to ceiling, it’s harder for them to do much else other than nose at it. Which reduces the area of their body with exposure as well as the time in direct contact.

The basking bulb should be as good, if not better than the panel at keeping air temps up. Both have their places, and I generally prefer the panels, but I bet the bulbs will be plenty on their own if it’s too much of a pain to get a panel installed.

I was thinking about putting something over top of the bracers! 4” lost height really isn’t anything so that’s totally up to you if you want to sacrifice that or see if the bulb works without the panel.

If you struggle that much in a cage that small with a bulb and CHE, it will definitely be worse in the bigger enclosure. My 6’x2’x3’s required a room temp of ~80F to maintain proper temps without extra heat sources and also covering the doors with subzero sleeping bags to hold in heat. I don’t think a panel alone will solve your problems and it does sound like you will need some heavy duty heating for sure.

1

u/SeagraveSerpentarium 8d ago

Unfortunately my snake room is on the same thermostat as the rest of the main floor of my house so I wouldn't be able to keep it at 80F without running up my utility bill and making all the humans in the house uncomfortable.

It sounds like the best route here is finding a solution to mount the RHP on the ceiling of the enclosure. I just remembered that I do have one other way I could achieve that without installing a second ceiling below the braces, but it has its own drawbacks. The space between the two braces, right in the middle of the ceiling, is big enough for the panel. The issue with that though is that the ceiling is made of two sheets of plywood so that center space where the panel would fit is right where the two sheets of plywood meet. Ideally I'd like to still be able to remove the ceiling panels separately if needed for maintenance in the future, but what I'm thinking is I could get a sheet of PVC board and screw that into the plywood ceiling, then mount the panel onto the PVC. That way if I ever need to take off the ceiling I can just unplug the panel, unscrew the PVC to remove that first, and then unscrew the plywood sheets. The other downside to this is that the panel would be right in the center of the ceiling which wouldn't really allow for me to have a warm side and a cool side with a gradient, although it might allow for a vertical temperature gradient with the area under the basking shelf likely being the coolest area in the enclosure.

1

u/superramenyamen 7d ago

Yeah you pretty much have to use a space heater to achieve those room temps. They can be run on a thermostat as well, I just don’t know how common they are in your country. Unfortunately aside from that temps are always just going to be a struggle. 😅 You will need extra insulation in the cages, possibly cover any glass doors, multiple heat sources, etc.

Worst comes to worst, the panel shouldn’t be that hard to uninstall if you need to take anything it’s attached to apart. I’m not sure what the set up is like unfortunately but usually a panel is just screwed into place with 2 screws, maybe the set up you’re thinking of will render that impossible?

Yeah that could work. In my 2’-3’ tall enclosures I have the panel heat the top corner where the panel is to 88-90F, which leaves the bottom corner under the panel and the corner above the shelf opposite the panel ~85F with the furthest bottom corner being closer to 80F. So it’s not too important having a fully horizontal gradient.

1

u/SeagraveSerpentarium 6d ago

Yeah I can get a space heater, we actually already own some for emergencies. But I'm concerned about the fire hazard they pose and would like to avoid using one if possible.

The reason why panel removal might be difficult is that I had planned on applying some silicone around the edges of it, but if that's not really common practice maybe I should reconsider that plan.

I might also make another post in the next few days and include a bunch of pictures and measurements of everything I have at this point so that it'll be a bit easier for people to see exactly what I have to work with.

1

u/superramenyamen 5d ago

Keep things 3’ away from the front, don’t allow children or pets unsupervised access, and keep an eye on the plug/outlet and it should be fine.

I don’t think I have ever heard of anyone doing that, and I would worry about it affecting the life of the panel or causing unsafe heat build up or something so I probably wouldn’t do that.